12V LCD Spot Welder Welding Machine Input Line Welding 90-150A PCB Circuit Board

Description

Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
12V LCD Spot Welder Welding Machine Input Line Welding 90-150A PCB Circuit Board
Popular
Popular
Product Introduction
Product introduction:
The user of this product needs to prepare a 12V battery for power supply, and the welding current is about 90A~150A. It is easy to weld the common 0.1mm~0.15mm nickel plated sheet. After several generations of product updates, it is now upgraded to automatically trigger welding and release the finger of the button.
System voltage: 12V-14.6V (below 12V will stop)
Operating current: 90-150A (lower than 90A current will not be able to weld firmly, higher than 200A current will damage the board, note that this refers to the short-circuit current, not the battery capacity. The battery capacity unit is: AH)
Battery recommendation:
①
36-45ah start-up lead-acid battery with good performance and small internal resistance (you must be able to start a car, but not more than 45AH. If the battery is too large, the board will burn, if it is too small, it will not work. If it is a motorcycle If the performance of the battery is not good, you can connect 2 batteries in parallel to increase the current)
②
3.5-5.5ah 3S model airplane lithium battery pack above 45C
③
High-rate lithium battery pack, etc.
Switch function:
Press the switch for 1.5 seconds to switch (blue light: low power, green light: medium power, red light: high power)
Package Included:
Circuit board x1
Into the wire x2
0.1*6mm nickel sheet x1
Soldering pen X2
Screw X3
Copper ear X4
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
12V LCD Spot Welder Welding Machine Input Line Welding 90-150A PCB Circuit Board
Product Introduction
Product introduction:
The user of this product needs to prepare a 12V battery for power supply, and the welding current is about 90A~150A. It is easy to weld the common 0.1mm~0.15mm nickel plated sheet. After several generations of product updates, it is now upgraded to automatically trigger welding and release the finger of the button.
System voltage: 12V-14.6V (below 12V will stop)
Operating current: 90-150A (lower than 90A current will not be able to weld firmly, higher than 200A current will damage the board, note that this refers to the short-circuit current, not the battery capacity. The battery capacity unit is: AH)
Battery recommendation:
①
36-45ah start-up lead-acid battery with good performance and small internal resistance (you must be able to start a car, but not more than 45AH. If the battery is too large, the board will burn, if it is too small, it will not work. If it is a motorcycle If the performance of the battery is not good, you can connect 2 batteries in parallel to increase the current)
②
3.5-5.5ah 3S model airplane lithium battery pack above 45C
③
High-rate lithium battery pack, etc.
Switch function:
Press the switch for 1.5 seconds to switch (blue light: low power, green light: medium power, red light: high power)
Package Included:
Circuit board x1
Into the wire x2
0.1*6mm nickel sheet x1
Soldering pen X2
Screw X3
Copper ear X4
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.