Brushless Spindle Motor 500W ER16 48V DC Motor Driver 55mm Clamp for CNC Router

Description

Features of brushless motors: 1. Brushless and low interference. The brushless motor removes the brush. The most direct change is that there is no electric spark generated when the brushed motor is running. This greatly reduces the electric spark's interference to remote control radio equipment. 2. Low noise and smooth operation. The brushless motor has no brushes, and the friction is greatly reduced during operation. The operation is smooth and the noise is much lower. This advantage is a huge support for the stability of the equipment. 3. Long life, low maintenance cost, without brush, the wear of brushless motor is mainly on the bearing. From a mechanical point of view, brushless motor is almost a maintenance-free motor, (the least life is brushed 10 times of the motor) When necessary,
Store category
Sign Up Now !
You may also like
Brushless Spindle Motor 400W ER16 48V DC Motor Driver 55mm Clamp for CNC Router
Product Description
Features of brushless motors:
1. Brushless and low interference. The brushless motor removes the brush. The most direct change is that there is no electric spark generated when the brushed motor is running. This greatly reduces the electric spark's interference to remote control radio equipment.
2. Low noise and smooth operation. The brushless motor has no brushes, and the friction is greatly reduced during operation. The operation is smooth and the noise is much lower. This advantage is a huge support for the stability of the equipment.
3. Long life, low maintenance cost, without brush, the wear of brushless motor is mainly on the bearing. From a mechanical point of view, brushless motor is almost a maintenance-free motor, (the least life is brushed 10 times of the motor) When necessary, just do some dust removal maintenance.
Product parameter:
Spindle motor: brand new brushless DC motor (original imported NSK bearing)
Working voltage: 48VDC need brushless drive, motor to run
Power: 500W
Speed: 12000r/min
Torque: 0.6 (N.m)
Insulation resistance: >2 megohm
Insulation dielectric strength: 400V
Motor diameter: 57mm (the fixed body part is 55mm)
Motor output shaft: from the previous 8mm thickened to 10mm
Length of the chuck part: 37mm of the shank, (including nut and sandwich 47mm)
Diameter of the chuck part: 20mm
Total motor length: 200mm (including clamping part and motor)
Spindle net weight: 1.54KG
The radial runout of the spindle is about 0.02-0.05.
Can be used to engrave materials such as metal or non-metal.
This spindle is equipped with forced air cooling and can work for a long time.
Driver:
1. Product features:
1. Model: HQ-WS500X
2. Working voltage: DC12V-DC52V
3. Drive current: rated 12A, peak value 15A.
4. Drive power: ≤500w (related to working voltage)
5. Closed loop and stable speed, the motor can still maintain the speed under heavy load
6. Pure hardware design, high speed, high anti-interference ability
7. External potentiometer control, analog voltage 0-5V, 0-10V
8. Forward and reverse control, frequent start and stop function, EN enable control
9. Over current short circuit protection and indication
10. With speed signal output function
Name:
DC+ DC-: DC voltage input terminal 12-52VDC
UVw: motor phase wire
HALL+: Hall power supply positive
HA HB HC: Hall signal line
HALL-: Hall power negative pole
5V: Control signal power supply 5V
VR: 0-5V speed control signal input terminal
GND: common terminal of control signal power supply
0-10V: 0-10V analog signal input terminal
Z/F: Positive/reverse control signal terminal
EN: Enable control input
PG: Speed ​​signal output terminal
ALM: fault alarm output terminal
Function description:
1. DC+, DC-: power input
Support 12~52VDC, DC power input, usually switch power supply or battery power supply, users must
Note that the voltage should not exceed 55VDC to avoid damage to the drive. The rated output current of the power supply should be greater than the drive output.
1.5 times the current. When using a switching power supply, pay attention to its nominal rated output current, and try to buy a switching power supply (1.2 times) that matches the phase current of the motor.
2. U, V, W: motor phase wires
Three phase wires of brushless DC motor. Be sure to pair with the Hall for correct wiring, and--be sure to tighten the screws. So as not to burn the drive due to excessive current.
3. HA, HB, HC: Hall (Hl) signal lines
When running, it must be paired with the phase item and wired correctly.
4. HALL+, HALL-: Hall power cord
Hall (Hll) power supply.
5. VR: Speed ​​control signal input
Support external 10K potentiometer or analog voltage speed regulation. When an external potentiometer is connected, VR corresponds to the middle pin of the potentiometer, and 5V and GND correspond to the two pins of the potentiometer. When an analog voltage (0-5V) is connected, GND is the reference ground, VR is the analog voltage input signal, and 5V is floating.
6. 0-10V: Analog signal input port
When an analog voltage (0-10V) is connected, GND is the reference ground, and the 0-10V port is the analog voltage input port.
7. ZF: Motor direction control
Forward and reverse direction control port. When floating or connected to 5V, it is reverse, and connected to GND is forward.
8. EN: Enable signal.
It cannot be left floating. When starting the motor, it must be connected to GND. The user can control the start or stop of the motor by controlling the on and off of the driver's EN terminal and GND.
9. PG: motor speed feedback output
Actual speed pulse signal = number of pole pairs*3.
10.ALM: Alarm and fault signal output
Alarm and fault signal output, when the drive is abnormal, output low level at ALM end
11. LED indicator
Always on during normal work (RUN), flashing when there is a failure (ALM)
Package Includes:
1 x Brushless Motor
1 x Motor Driver
1 x Clamp
1 x Potentiometer and Switch
Payment
Delivery details
Terms of sales
About us
Contact us
Payment
We accept ebay payment 。
Fees such as import duties, taxes are not included in the item price or shipping costs. These charges are the buyer's responsibility.
Delivery details
Shipping:
The item will be shipped from our US warehouse to United States, which is more faster than from aboard.
2-9 working days to: USA
Terms of sales
We maintain high standards of excellence and strive for hundred percent customer satisfaction. Feedback is very important to us. We hope that you contact us immediately before you give neutral or negative feedback, so that we can address your concerns. It is impossible to address issues if we do not know about them!
About us
Your satis
faction is our ultimate goal. We work hard to earn your trust and future business. Our certified technicians have tested each item before shipping. The unit comes with 1 year limited warranty on all manufacturing defects.
a) If you receive a defective item, you may return it or ask for a discount. Please contact us within 14 days after you receive the package.
b) What you returned must be intact and in its original packaging as re? u. Customer is responsible for shipping costs of the returned item.
c) We will cover the cost of shipping back t with the shipping rate indicated in the registration page. We will send you a new unit or refund the full payment you paid.
Thank you.
Contact us
Business Hour
Business Hour: Monday To Friday: 8:30 AM to 5:00 PM (Beijing China time)
Due to time zones, our reply to your questions may not be immediately. But within above working time, we will reply your email within 24 hours. If it's non-workdays, please kindly be patient and wait till Monday.
Please contact us with ebay message.
Please feel free to contact us if you have any questions.
: Monday To Friday: 8:30 AM to 5:00 PM (Beijing China time)
Due to time zones, our reply to your questions may not be immediately. But within above working time, we will reply your email within 24 hours. If it's non-workdays, please kindly be patient and wait till Monday.
Please contact us with ebay message.
Please feel free to contact us if you have any questions.
Feedback
On Jul-08-21 at 02:22:05 PDT, seller added the following information: