LCD Display Mini Spot Welder Machine Set Battery Welding Power Supply DIY

Description

LCD Display Mini Spot Welder Machine Set Battery Welding Power Supply DIY
Features:
100% brand New and high quality.
A Wide Selection of Welding Power Supply: Lithium battery power supply or 12V car battery.
The controller is controlled by a single-chip microcomputer, and the output pulse is accurate to ensure the welding quality.
With an LCD display screen, can display welding parameters.
The welding pen and the input line are connected by U-shaped cold-pressed terminals, which are convenient for disassembly and replacement.
Using automatic touch welding mode, while retaining the manual trigger interface, you can choose according to your own use.
The power board uses 2 Gusi copper to increase the overcurrent capacity. Using 5 300A MOS tubes, non-disassembled MOS tubes.
The MOS tube driver adopts the imported special chip driver. The fastest MOS tube can be hit with 20nS. The switch is fast to prevent the explosion of the tube and the non-triode push-pull drive.
The MOS drive design adds a transient diode to protect the MOS and prevent the explosion of the tube.
10AWG multi-filament flexible wire is used for the welding pen line and the input line to increase the overcurrent capacity.
The controller is mainly for welding nickel-plated steel strips from 0.1mm to 0.15mm.
A 25V10000uF high-frequency low-resistance capacitor is added to the power input for energy compensation, which increases welding stability.
Specification:
Material: Metal
Input Line Length: App.20cm
Length of Welding Pen: App.30cm
Color: Red+Blue+Black
Battery: Lithium battery
(Not Included)
Instructions for use:
1: Power connection
The controller comes with a 20cm long 10AWG input wire.
One end has been crimped with a U-shaped terminal, and the other end has not been processed.
Connect the crimped U-shaped terminal to the control power input terminal, and the other end is processed according to its own power supply.
Do not connect the negative electrode wrong.
2: Switch on and off
There is a power switch under the control board.
After pressing, wait for 3 seconds.
After the buzzer drops, the LCD lights up and the boot is complete.
Press the power switch again to shut down.
3: Screen description and parameter adjustment.
4: Welding
Keep the welding pin clean.
If the welding pin is polished into a round head, the welding effect can be improved.
There are manual and automatic methods.
Package Included:
1 x Controller
(
Battery
Not Included
)
2 x of Welding Pen
2 x of Power Input Line (Red and Blue)
1 Pair of U-Shaped Cold-Pressed Terminal (Used to Connect to Input Power)
Payment must be received in 2 business days of auction closing.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Items will be shipped within 2 business day on payment received.
Items are shipped from US local warehouse via UPS&USPS&FEDEX
Delivery time depends on destination and other factors, it may takes up to 2-9 business days.
If the item is defective, please notify us within days after the receipt of the item.
The item shall be return in its original condition, in order to get it refunded or replaced.
The item is not refundable after 14 days, it will only be repaired.
Buyer is responsible for all shipping costs
We are pursuing 100% satisaction positive feedback and 5 star rating.
Please feel free to contact us before leaving a negative feedback or low DSR.
Please contact us before you open dispute on ebay and paypal, we will offer you best service.We will reply in 24 hours and solve your problem in a friendly way.
Please feel free to contact us by ebay message instead of email, we will reply all the ebay messages within 24 hours.
Features:
100% brand New and high quality.
A Wide Selection of Welding Power Supply: Lithium battery power supply or 12V car battery.
The controller is controlled by a single-chip microcomputer, and the output pulse is accurate to ensure the welding quality.
With an LCD display screen, can display welding parameters.
The welding pen and the input line are connected by U-shaped cold-pressed terminals, which are convenient for disassembly and replacement.
Using automatic touch welding mode, while retaining the manual trigger interface, you can choose according to your own use.
The power board uses 2 Gusi copper to increase the overcurrent capacity. Using 5 300A MOS tubes, non-disassembled MOS tubes.
The MOS tube driver adopts the imported special chip driver. The fastest MOS tube can be hit with 20nS. The switch is fast to prevent the explosion of the tube and the non-triode push-pull drive.
The MOS drive design adds a transient diode to protect the MOS and prevent the explosion of the tube.
10AWG multi-filament flexible wire is used for the welding pen line and the input line to increase the overcurrent capacity.
The controller is mainly for welding nickel-plated steel strips from 0.1mm to 0.15mm.
A 25V10000uF high-frequency low-resistance capacitor is added to the power input for energy compensation, which increases welding stability.
Specification:
Material: Metal
Input Line Length: App.20cm
Length of Welding Pen: App.30cm
Color: Red+Blue+Black
Battery: Lithium battery
(Not Included)
Instructions for use:
1: Power connection
The controller comes with a 20cm long 10AWG input wire.
One end has been crimped with a U-shaped terminal, and the other end has not been processed.
Connect the crimped U-shaped terminal to the control power input terminal, and the other end is processed according to its own power supply.
Do not connect the negative electrode wrong.
2: Switch on and off
There is a power switch under the control board.
After pressing, wait for 3 seconds.
After the buzzer drops, the LCD lights up and the boot is complete.
Press the power switch again to shut down.
3: Screen description and parameter adjustment.
4: Welding
Keep the welding pin clean.
If the welding pin is polished into a round head, the welding effect can be improved.
There are manual and automatic methods.
Package Included:
1 x Controller
(
Battery
Not Included
)
2 x of Welding Pen
2 x of Power Input Line (Red and Blue)
1 Pair of U-Shaped Cold-Pressed Terminal (Used to Connect to Input Power)
PAYMENT
Payment must be received in 2 business days of auction closing.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
SHIPPING
Items will be shipped within 2 business day on payment received.
Items are shipped from US local warehouse via UPS&USPS&FEDEX
Delivery time depends on destination and other factors, it may takes up to 2-9 business days.
Terms of Sale
If the item is defective, please notify us within days after the receipt of the item.
The item shall be return in its original condition, in order to get it refunded or replaced.
The item is not refundable after 14 days, it will only be repaired.
Buyer is responsible for all shipping costs
ABOUT US
We are pursuing 100% satisaction positive feedback and 5 star rating.
Please feel free to contact us before leaving a negative feedback or low DSR.
Please contact us before you open dispute on ebay and paypal, we will offer you best service.We will reply in 24 hours and solve your problem in a friendly way.
Please feel free to contact us by ebay message instead of email, we will reply all the ebay messages within 24 hours.