New Portable Mini Spot Welder Machine Battery Various Welding Power Supply 18650

Description

DIY Portable Mini Spot Welder Machine 18650 Battery Various Welding Power Supply
Brand New And High Quality
Description:
1.Wide choice of welding power source: lithium battery power source or 12V car battery.
The controller is controlled by a single-chip microcomputer, and the output pulse is accurate, which en
sures the welding quality.
2.With LCD display, welding parameters can be displayed.
3.The soldering pen and the input wire are connected by U-shaped cold-pressed terminals, which is convenient for disassembly and replacement.
4.Use the automatic touch welding mode, while retaining the manual trigger interface, you can choose according to your own use.
5.The power board uses 2 strands of bronze to increase the overcurrent capacity. Use 5 300A MOS tube, undisassembled MOS tube.
6.MOS tube driver adopts imported special chip driver. The fastest MOS tube can reach 20nS. The switch is fast and can prevent the explosion of electronic tube and non-triode push-pull drivers.
7.The MOS driver design adds a transient diode to protect the MOS and prevent the lamp from exploding.
The 10AWG multi-filament flexible wire is used for soldering the pen wire and the input wire to increase the overcurrent capability.
8.The controller is mainly used for welding 0.1mm to 0.12mm nickel-plated steel strip.
9.A 25V10000uF high-frequency low-resistance capacitor is added to the power input terminal for energy compensation, thereby improving the welding stability.
Specification:
Size: 10CM*5CM*3CM
Material: Metal
Input line length: about 20cm / 7.87in(Red and Black)
Soldering pen length: about 30cm / 11.81in
Color: red + blue + black
Battery: Lithium battery (not included)
Welding materials:
Welding 0.1 to 0.12mm thick nickel-plated steel strip
Energy setting:
The energy must gradually increase from 01, and the maximum value cannot exceed 50.
Exceeding the above conditions may damage the controller.
Battery selection:
1: 12V car battery (25-40ahah), requires good performance and low internal resistance
2: 4000 to 6000mAh 45C to 60C 3S model aircraft lithium battery
3: 30 to 35ah 12V capacity lithium battery pack
Instructions for use:
1: Power connection
The controller comes with a 20cm long 10AWG input wire. One end has been crimped with a U-shaped terminal, and the other
end has not been processed. Connect the crimped U-shaped terminal to the control power input terminal, and the other end is
processed according to its own power supply. Do not connect the negative electrode wrong.
2: Switch on and off
There is a power switch under the control board. After pressing, wait for 3 seconds. After the buzzer drops, the LCD lights up and
the boot is complete. Press the power switch again to shut down.
3: Screen description and parameter adjustment.
There are currently three parameters on the screen:
WELD ENERGY: Welding energy, parameters 01-99
INPUTE: power supply voltage, display the current input power voltage
WELD WAY: Welding method, there are MANUAL manual and AUTO manual
Welding energy adjustment: It can be adjusted directly by pressing the up and down buttons;
Welding method selection: It can be switched by pressing the button.
4: Welding
Keep the welding pin clean. If the welding pin is polished into a round head, the welding effect can be improved. There are manual and automatic methods.
NOTE:
T
his controller is mainly for maintenance or friends who play with power banks, power tools, and airplane models. Because the amount of battery to be welded is not so large, it is not cost-effective to make a transformer welding machine. Therefore, this controller is more Suitable for. Find 3 3S 50C 5000mAH, or 12V/50AH or more batteries, you can weld. Very convenient.
When designing this controller, we try our best to reduce the requirements of users, but users still need to have a certain electronic foundation and safety awareness.
Although adequate design and protection of the drive of the MOS tube have been made during the design, it is inevitable that the explosion of the tube will occur during use. If there is a explosion, just replace one.
Package Includes(As the picture show):
1 x Controller
2 x of Welding Pen
2 x of Power Input Line (Red and Blue)
1 Pair of U-Shaped Cold-Pressed Terminal (Used to Connect to Input Power)
1 x User Manual
Payment：
Paypal Preferred.
Local pickup NOT available at this time.
Shipping
：
1.We process your order within 1 business day upon payment (Note: NOT counting holidays or weekends).
2.We only ship to the confirmed address provided by ebay. Before you pay, please make sure your address in ebay matches the address you would like us to ship to.
3.We strive our best to provide you the most reliable, affordable way of shipping service. But sometimes delivery is highly depended on the courier company. If you do not receive your item on time, please contact us immediately for further assistance. Thank you for your understanding.
Return & Refund
1.We operate a 30 day money back guarantee. Please read the item description and check the pictures carefully before bidding. Return or refund is available only if item DOA or there's error in item description causing the item not fitting your need. In such cases, seller pays for all related shipping cost if any.
2.Returns are also acceptable if buyer purchased this by mistake and item still in good condition for reselling. Buyer is responsible for all related shipping cost.
3.Please avoid making negative feedback remarks, contact us first if you have any problems! We are here to help!
We use an automated eBay feedback response system. If you are happy with the product, please leave positive feedback and we will automatically leave positive feedback for you. If you are unhappy with the transaction for any reason, please contact us first to resolve. When you don’t leave negative feedback, we are still very responsible store, so you don't need to leave negative feedback to get a satisfactory reply.We will correct our problem in time so that the future buyer will not have the same problem.
Feedback
1.Before leaving us neutral or negative feedback, please contact us first. We will do everything we can to give you a satisfying solution.
2.Please don't open case via ebay or paypal.
3.Please don't open any return request before contact us.
4.We do our best to resolve any issue. Leaving negative feedbacks and low ratings doesn't get things solved. So please talk with us and we will not let you down.
We maintain high standards of excellenceand
strive for 100% customer satisfaction!
Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral
or negative
feedback, so that we can satisfactorily address your concern