Pneumatic Spot Pulsing Point Welding Machine Battery Pulse Type Spot Welder

Description

20140320
220V Air Pulsing Point Welding Machine
Introduction
The machine is controlled by 8 bit microcomputer. The welding is reliable and  reliable, and the solder joint is beautiful.
Apply to stainless steel, copper, aluminum, alloy and other similar or  dissimilar metal welding.
Principle
The principle of pneumatic AC pulse type resistance welding is that the 220V  power is changed into low voltage by using welding transformer, and the low  voltage and high current are output at an instant, so that the welding workpiece  has high temperature and the forging force is reached to achieve the purpose of  welding.
Parameters
Project
P
arameters
Welding method
AC pulse
Pulse number
1-5
Energy  regulation
1-999
Electrode  pressure
1-4kg
Electrode  stroke
15mm
0.59inch
Length of  welding arm
70mm
2.76inch
Rated capacity
3kw
Rated input  voltage
AC220V
±
10%
Rated input  current
10A
Rated input  pressure
0.6Mpa
Secondary  no-load voltage
4V
Secondary  maximum current
5000A
Net weight
15kg
Outline size
40*15*31 cm
15.75*5.91*12.2inch
Install, join
1.
M
ounting  electrodes
Loosen the electrode locking screw, put the electrode into the corresponding  hole of the electrode fixing seat, adjust the electrode height and lock the  electrode locking screw.
2.
C
onnecting  foot switch
Insert the foot switch joint into the foot switch interface and tighten the nut  of the foot switch joint.
3.
C
onnecting  gas source
A  compressed air connector corresponding to the compressed air interface is  inserted into the compressed air interface.
4.
C
onnecting  power supply
Plug the power plug into the corresponding 220V/10A socket.
Adjustment
Instructions:  press "press" in the following instructions to press the button and then  loosen. "Long press" means press the button to hold for more than 1  seconds.
Switch on the power switch and enter the standby mode.
1.
W
elding  energy adjustment
In  the standby mode, press the function key of the control panel to enter the  setting state, and the POWER status light starts flashing. Press one "+ key"  welding energy, plus one, press long "+ key" welding energy increase rapidly;  press one "key" welding energy to reduce one, long press "key" welding energy to  reduce rapidly. Press the four function key to save the setup parameters and  exit the set state to enter the standby mode.
The welding energy value is related to the output current: the greater the  welding energy, the greater the output current, and vice versa. The welding  energy adjusted to the appropriate value, in order to ensure the welding work of  solid and not "breakdown" or "false" phenomenon.
2.
W
elding  pulse adjustment
In  the standby mode, press the "function key" of the two control panel to enter the  setting state, and the CYCLE status light starts flashing.
Press one "+ key" welding pulse number plus one, press one "key" welding pulse  number minus one. Press the three function key to save the setup parameters and  exit the set state to enter the standby mode.
The number of welding pulses is the number of pulses to be welded. Less welding  pulse number should be used for workpieces with lower melting point or thinner,  and more welding pulse should be used for workpieces with higher melting point  or thickness. Generally, the number of welding pulses is recommended to be 2.
3.
P
reload  time adjustment
In  the standby mode, press the "function key" of the three control panel to enter  the setting state, and the DELAY status light starts flashing. Press a "+ key"  welding preload time, plus one, long press "+ key" welding preload time  increased rapidly; press a "key" welding preload time minus one, long press  "key" welding, pre pressing time is reduced rapidly. Press the two function key  to save the setup parameters and exit the set state to enter the standby mode.
Preloading time value and the head start this period of time to discharge  welding related action: preloading time the greater the value from head start  action to discharge welding time is longer, and the shorter period. Adjust the  preload time to the appropriate value to ensure that no "fire" or "slow welding"  phenomenon occurs during the welding process.
4.
W
elding  mode adjustment
In  the standby mode, press the "function key" of the four control panel to enter  the setting state, and the MODE status light starts flashing. Press one "+ key"  welding mode plus one, press one "key" welding mode to reduce one. Press the  "function key" to save the setup parameters and exit the set state to enter the  standby mode.
Welding mode 1: standby mode, closed pedal switch, horn down and put pressure on  the workpiece discharge welding, welding head reduction, complete a welding,  enter the standby state. This mode applies to normal welding.
Welding mode 2: standby mode, closed pedal switch, welding head down and put  pressure on the workpiece, press the "+" button for discharge welding or release  the foot switch reset head. This mode is suitable for debugging welding.
Welding mode 3: standby mode, closed pedal switch, welding head without action  and immediately discharge. This mode is suitable for hand welding of welding arm  and extension line.
5.
E
lectrode  height adjustment
Loosen the electrode locking screw, adjust the electrode to the proper height,  and then lock the electrode to lock the screw.
6.
W
orktable  height adjustment
Unscrew work table adjusting screw, adjust worktable to proper height and lock  screws.
7.
E
lectrode  pressure adjustment
Pull up the pressure regulating valve knob, rotate clockwise, increase the  electrode pressure, turn counterclockwise, reduce the electrode pressure, adjust  to the proper pressure, then push the pressure valve knob to the inside.
8.
Weld
ing  arm rising speed adjustment
Loosen the locking nut of the rising speed control valve, rotate the speed  regulating valve clockwise, slow down the rising speed of the welding arm, speed  up the speed of the welding arm counterclockwise, adjust to the proper speed,  then screw the nut tightly.
9.
We
lding  arm falling speed adjustment,
Loosen the locking nut of the descending speed control valve, rotate the speed  reducing valve clockwise, slow down the speed of the welding arm, rotate the  speed valve counterclockwise, speed up the welding arm, adjust to the proper  speed, then screw the nut tightly.
Welding
After fifth adjustments, welding machine can carry out welding operations.
The workpiece to be welded securely placed on the work table, adjust the work  piece and the corresponding position of the table, close a foot switch, welding  arm decline, the welding workpiece pressing, welding machine will automatically  complete a welding.
Maintenance
1.
The
welding machine must  not turn off the power supply when the parameter is set. The incorrect shutdown  of the power supply may cause the setting parameter to be unable to save or the  parameter is out of order.
2.  when the welding machine stops working, it should turn off the power supply.  Unplug the power plug and the compressed air plug for long periods of time.
3.  try to make sure the electrodes are clean and smooth. When the oxide layer  appears on the electrode surface, the surface oxide layer can be removed by  abrasive tools.
4.  keep enough oil in the oil mist. When the lubricating oil is not enough, you can  add lubricating oil from the filler hole. It is recommended to use ISO, VG32 or  the same grade lubricant.
Item  included:
220V Air Pulsing  Point Welding Machine  (151006)
Item##
Description
QTY
Unit
151006
220V Air Pulsing Point Welding  Machine
1
set
Shipping & Handling  Details
Shipping & Handling Details
Default  Shipping Cost or Free Shipping Information:
▲
Default  shipping cost or free shipping service is only for the customers  from Canada or the lower 48 United States by Canada Post, USPS or  the UPS Ground. Customers from other areas or needs other shipping  ways, please contact us.
▲
Buyers  from Guam, Puerto Rico, Virgin Islands, American Samoa, Alaska,  Hawaii, PO Boxes, APO/FPO addresses or other countries/areas, there  WILL be extra shipping costs, please contact us for more detailed  information.
▲
Please  make sure your address is valid for both UPS and USPS services. Any  costs incurred because of incorrect or undeliverable address should  be undertaken by buyer.
Handling Time:
Shipping  is usually made in 1-3 business days after payments cleared. Orders  are processed from Monday-Friday; Not on the weekends & public  holidays.
Sales tax / Customs  duties:
Any  sales taxes or Customs duties are not included. If came out, they  must be undertaken by the buyer.
Damage In Shipping:
Email  or call us First! We will work with you to get the case resolved in  the fastest method.
Return /  Refund
If you are not 100% happy with your purchase, please  contact Us. Please don't directly opened a request or case without  informing us, or else, we will do some discounts on the warranty and  other sales-services later on. Hope for your understanding.
Returns & Exchanges
▲
All  returns must be made within 14 days of delivery date. Items must be  in new, unused condition, with all original materials included with  the shipment. A partial refund may be applied for opened or damaged  items, depending on the condition.
▲
Items  returned under the buyer’s remorse: The return shipping fee must be  covered by the buyer; The original shipping cost will also be  deducted from the refund. 15% restocking fee of the items purchase  price will be charged.
▲
Returns  that are the result of our seller's error: Buyer will receive a full  refund of the item as well as shipping charges
▲
All returns require  a RA (Return Authorization) number that will be given by our seller.  Please contact with us at first for more details.
Defective & Damaged Products
▲
If  product was received damaged or not as described, please send us  some pictures or videos, so we could well understand your problem,  then solve them for you ASAP. Besides, it's much helpful for us to  claim with UPS, remind our related department to pay much more  attention to packaging later on. Hope for your understanding.
▲
Replacement  or refund of defective or damaged products can only be returned in  exchange for the exact same product, or else, the purchase price  will be refunded back to your original payment method.
▲
If  an item is received damaged, customer service must be contacted  within 7 days of receiving your item. All returns require a RA  (Return Authorization) number as above.
Payment
eCheck Issues:
Payments via  eCheck do not clear immediately. Usually you will wait 5-7 days  after checkout for it to clear. Then we will arrange shipments  for you.
Warranty & Feedback
▲
6  months' warranty for the machines, not for the consumables. We stand  behind our products all the item, so even if your warranty period  has expired, you can still seek for service or technical support  from us with low cost.
▲
Any  warranty shipping cost to us is responsible by buyer.
▲
Any  shipping cost to buyer is responsible by the seller.
▲
We  committee to the customer satisfaction and want to bring you the  best purchase experience. If there is any problems, please contact  us ASAP. If not, please leave us a positive feedback as it's very  important for us. Thanks very much.