Portable DH20 Pro Spot Welder Welding Machine Power W/ Welding Pen Nickel Plate

Description

Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
Portable DH20 Pro Spot Welder Welding Machine Power W/ Welding Pen Nickel Plate
Popular
Popular
Product Introduction
Description:
- DH20 Pro Spot Welder Upgrade to V2.0 Version
*Take note to fully charge the battery before use*
Since the built-in battery is a high-rate discharge battery, for transportation and storage safety, the battery power is very low and welding operations are not possible before charging.
It's recommended to weld nickel sheets below 0.15mm.
Features:
- Portable spot welding machine, with quick release welding pen.
- Compact and portable size design can easy to take belong;
- Integrated welding pen use gold-plate terminal, with good conductivity and low contact resistance;
- Thickened pure copper strip and imported MOS tube can save energy and can provides longger service time;
- Built-in high rate power battery, with fine charge and discharge performance, more stable;
Specifications:
- Name: Spot Welding Machine
- Material: Metal Case
- Battery Capacity: 5500mAh
- Welding Output:  4.2V Max 639A
- Welding Thickness: 0.1-0.15mm
- USB Output:5V Max 2.4A
- Charging Port: Type-C
- Product Weight: 302g
- Product Size: 103x83x29mm
- Package size: 143x107x48mm
- Package weight: 407g
Packaging Include:
- 1 x DH20 Pro+ Welding Machine
- 1 x Welding Pen
- 1 x 0.12mm*8mm*2m Nickel Plated Steel Belt
How to Use:
*Take note to fully charge the battery before use*
1. To Turn On/Off - Long press button for 3 seconds then release the button after hearing the boot sound,that is turn on/off.
2. Short press the button. If the buzzer rings, that is shift position. Press one time, and it can add 1 gear. 1-9 cycles, and the 9th gear is the strongest welding strength.
3. Soldering Operation - Start with level 1, unit will start soldering after 0.5 seconds once it detects item. Power setting can be adjusted to suit different soldering job. If high level going into current protection mode and reboot,you can connect a USB input;
4. Auto Power Off - After no activity for 15 minutes the unit will automatically shut down.
5. USB Output - The USB output will be activated automatically once connected. Once output current is less than 50mAh the unit will automatically cut power output. Short press button to resume power output.
6. Error Warning - If the device fails, the buzzer keeps beeping after turning on;
7. Firmware Update - The upgrade port is reserved, which can be upgraded to the latest firmware
Precautions
1. It's recommended to weld nickel sheets below 0.15mm (Can welding 0.15mm).
2. It's recommended to weld when battery power over 70% for better welding effect.
3. Pay attention to the placement of the soldering pen,if the  pressure of the soldering pen too loose,will break down the nickel sheet.
If the  pressure of the soldering pen too tightly,the welding will be week.
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
Portable DH20 Pro Spot Welder Welding Machine Power W/ Welding Pen Nickel Plate
Product Introduction
Description:
- DH20 Pro Spot Welder Upgrade to V2.0 Version
*Take note to fully charge the battery before use*
Since the built-in battery is a high-rate discharge battery, for transportation and storage safety, the battery power is very low and welding operations are not possible before charging.
It's recommended to weld nickel sheets below 0.15mm.
Features:
- Portable spot welding machine, with quick release welding pen.
- Compact and portable size design can easy to take belong;
- Integrated welding pen use gold-plate terminal, with good conductivity and low contact resistance;
- Thickened pure copper strip and imported MOS tube can save energy and can provides longger service time;
- Built-in high rate power battery, with fine charge and discharge performance, more stable;
Specifications:
- Name: Spot Welding Machine
- Material: Metal Case
- Battery Capacity: 5500mAh
- Welding Output:  4.2V Max 639A
- Welding Thickness: 0.1-0.15mm
- USB Output:5V Max 2.4A
- Charging Port: Type-C
- Product Weight: 302g
- Product Size: 103x83x29mm
- Package size: 143x107x48mm
- Package weight: 407g
Packaging Include:
- 1 x DH20 Pro+ Welding Machine
- 1 x Welding Pen
- 1 x 0.12mm*8mm*2m Nickel Plated Steel Belt
How to Use:
*Take note to fully charge the battery before use*
1. To Turn On/Off - Long press button for 3 seconds then release the button after hearing the boot sound,that is turn on/off.
2. Short press the button. If the buzzer rings, that is shift position. Press one time, and it can add 1 gear. 1-9 cycles, and the 9th gear is the strongest welding strength.
3. Soldering Operation - Start with level 1, unit will start soldering after 0.5 seconds once it detects item. Power setting can be adjusted to suit different soldering job. If high level going into current protection mode and reboot,you can connect a USB input;
4. Auto Power Off - After no activity for 15 minutes the unit will automatically shut down.
5. USB Output - The USB output will be activated automatically once connected. Once output current is less than 50mAh the unit will automatically cut power output. Short press button to resume power output.
6. Error Warning - If the device fails, the buzzer keeps beeping after turning on;
7. Firmware Update - The upgrade port is reserved, which can be upgraded to the latest firmware
Precautions
1. It's recommended to weld nickel sheets below 0.15mm (Can welding 0.15mm).
2. It's recommended to weld when battery power over 70% for better welding effect.
3. Pay attention to the placement of the soldering pen,if the  pressure of the soldering pen too loose,will break down the nickel sheet.
If the  pressure of the soldering pen too tightly,the welding will be week.
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.