Portable Spot Welder Integrated Welding Machine Spot Welding For 18650 Battery

Description

Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
Portable Spot Welder Integrated Welding Machine Spot Welding For 18650 Battery
Popular
Popular
Product Introduction
Purchase Notes:
1. After the user has the product, the battery is generally not fully charged. Please fully charge it before using it to get the best results.
2. This machine can weld 0.1-0.15mm nickel-plated steel sheet and 0.1 pure nickel sheet. It is not possible to weld pure copper materials with good conductivity.
3. Don't keep the battery power too low or too high if not used for a long time.
4. If the power consumption is too low, it will cause the microcontroller to not work, showing that the machine cannot be turned on, and the charging light does not turn on. If this happens, please charge it, and it will be restored after tens of minutes.
5. Current, voltage, and materials can affect the spot welding effect. Not all materials can get a good spot welding effect. What can now be adjusted is the spot welding time and contact strength. It is recommended to practice your hands with iron cans first, and then solder the battery after you are familiar with the welding machine.
6. This machine is DIY by hand, with slight scratches and burrs on the exterior, it is normal, and those with higher requirements should be careful when shooting.
The main parameters:
Single battery: 3.7V/5.5AH
Dual battery enhanced version: 3.7V/11AH
Pulse time: six gears adjustable (1-6-1 gear cycle, 6 gears maximum)
Trigger delay: 0.8 seconds
Adapted charger: 5V, current greater than 1A
Instructions for use:
1. Long press for 3 seconds, the buzzer will sound once, turn on/off
2. Short press the button, the buzzer will sound once, and the gears will be changed. Each press will increase by one gear, 1-6-1 cycle, 6 gears have the strongest welding strength. Observe the light after pressing the key. The light flashes several times in several gears. The gear will be stored automatically when it is turned off, and the gear will be stored by default next time it is turned on.
3. After the welding pen is pressed, the buzzer will sound and wait for about 1 second to trigger welding.
4. When charging, the button light will remind in the form of breathing light, and the light will always be on when it is full. The welding function is not available when charging.
5. If it does not work after working for a period of time, it may be that the power is too low, causing the MCU to not work, the charging light does not light up, and it does not turn on. At this time, it will be charged for half an hour and the voltage can be restored after the voltage rises.
Features of this machine:
1. Press and hold the spot welding for 3 seconds to turn on/off the buzzer. The low power consumption is soft and hard design. The measured current is a few uA when turned off. There is no need to worry that the battery will be consumed after a long time and affect the battery life.
2. Short press the gear position to add one digit, the last gear will be remembered when the machine is turned on, and the six gears will cycle.
3. This spot welder can automatically detect the trigger 0.8s after the soldering pen touches the nickel sheet. It does not require manual/foot triggering or interval time triggering. You need to click the soldering pen before judging the trigger time point, and the operating experience is first-rate.
4. With the special power management and software design of this welding machine, the gear will not return to zero without resetting during the welding process. When the battery power changes, the solder joints may become weak. You can increase the gear at this time. But it is recommended to charge as soon as possible.
5. When charging, the power light will remind in the form of breathing light, and the light will always be on when it is full. To prevent accidents during charging, the welding function is not available during charging.
6. It comes with a charging management control module, which can be charged through the mobile phone charging head (5V, output current at least 1A), with a USB charging cable
7. Comes with a 50C discharge high-rate lithium battery, which is fully charged with hundreds of solder joints with common nickel-plated sheets within 0.1mm-0.15mm.
Welding test:
First, press and hold the power button for 3 seconds. After hearing the buzzer sound, turn it on. There are 6 levels in total, 1-6-1 levels cycle. Short press in the power-on state, you will hear the buzzer beep once, add another level, and the power light The flashing display gears, flashing several times is the number of gears, in order to count accurately, after pressing the button, wait for the next flashing interval to start counting.
The above test is no problem. Press the soldering pen on the object to be welded and hear a buzzer sound, indicating that the soldering pen has been in contact, wait for about 1 second for welding, if the buzzer does not sound, press the soldering pen again.
Package Included:
1* Integrated welding machine
1* Soldering pen + 10AWG silicone wire
1* charger
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
Portable Spot Welder Integrated Welding Machine Spot Welding For 18650 Battery
Product Introduction
Purchase Notes:
1. After the user has the product, the battery is generally not fully charged. Please fully charge it before using it to get the best results.
2. This machine can weld 0.1-0.15mm nickel-plated steel sheet and 0.1 pure nickel sheet. It is not possible to weld pure copper materials with good conductivity.
3. Don't keep the battery power too low or too high if not used for a long time.
4. If the power consumption is too low, it will cause the microcontroller to not work, showing that the machine cannot be turned on, and the charging light does not turn on. If this happens, please charge it, and it will be restored after tens of minutes.
5. Current, voltage, and materials can affect the spot welding effect. Not all materials can get a good spot welding effect. What can now be adjusted is the spot welding time and contact strength. It is recommended to practice your hands with iron cans first, and then solder the battery after you are familiar with the welding machine.
6. This machine is DIY by hand, with slight scratches and burrs on the exterior, it is normal, and those with higher requirements should be careful when shooting.
The main parameters:
Single battery: 3.7V/5.5AH
Dual battery enhanced version: 3.7V/11AH
Pulse time: six gears adjustable (1-6-1 gear cycle, 6 gears maximum)
Trigger delay: 0.8 seconds
Adapted charger: 5V, current greater than 1A
Instructions for use:
1. Long press for 3 seconds, the buzzer will sound once, turn on/off
2. Short press the button, the buzzer will sound once, and the gears will be changed. Each press will increase by one gear, 1-6-1 cycle, 6 gears have the strongest welding strength. Observe the light after pressing the key. The light flashes several times in several gears. The gear will be stored automatically when it is turned off, and the gear will be stored by default next time it is turned on.
3. After the welding pen is pressed, the buzzer will sound and wait for about 1 second to trigger welding.
4. When charging, the button light will remind in the form of breathing light, and the light will always be on when it is full. The welding function is not available when charging.
5. If it does not work after working for a period of time, it may be that the power is too low, causing the MCU to not work, the charging light does not light up, and it does not turn on. At this time, it will be charged for half an hour and the voltage can be restored after the voltage rises.
Features of this machine:
1. Press and hold the spot welding for 3 seconds to turn on/off the buzzer. The low power consumption is soft and hard design. The measured current is a few uA when turned off. There is no need to worry that the battery will be consumed after a long time and affect the battery life.
2. Short press the gear position to add one digit, the last gear will be remembered when the machine is turned on, and the six gears will cycle.
3. This spot welder can automatically detect the trigger 0.8s after the soldering pen touches the nickel sheet. It does not require manual/foot triggering or interval time triggering. You need to click the soldering pen before judging the trigger time point, and the operating experience is first-rate.
4. With the special power management and software design of this welding machine, the gear will not return to zero without resetting during the welding process. When the battery power changes, the solder joints may become weak. You can increase the gear at this time. But it is recommended to charge as soon as possible.
5. When charging, the power light will remind in the form of breathing light, and the light will always be on when it is full. To prevent accidents during charging, the welding function is not available during charging.
6. It comes with a charging management control module, which can be charged through the mobile phone charging head (5V, output current at least 1A), with a USB charging cable
7. Comes with a 50C discharge high-rate lithium battery, which is fully charged with hundreds of solder joints with common nickel-plated sheets within 0.1mm-0.15mm.
Welding test:
First, press and hold the power button for 3 seconds. After hearing the buzzer sound, turn it on. There are 6 levels in total, 1-6-1 levels cycle. Short press in the power-on state, you will hear the buzzer beep once, add another level, and the power light The flashing display gears, flashing several times is the number of gears, in order to count accurately, after pressing the button, wait for the next flashing interval to start counting.
The above test is no problem. Press the soldering pen on the object to be welded and hear a buzzer sound, indicating that the soldering pen has been in contact, wait for about 1 second for welding, if the buzzer does not sound, press the soldering pen again.
Package Included:
1* Integrated welding machine
1* Soldering pen + 10AWG silicone wire
1* charger
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.